-
#900 Reply
Posted by
cream3000
on 08 Jan, 2020 18:50
-
What makes you think you run on high res right now though, can you post a radiometric image?
i watched the image in flir tools. there was written at the resolution that it is high. i compared to some stock pictures at 80x60.
going to upload something the next days.
-
#901 Reply
Posted by
Bud
on 08 Jan, 2020 19:18
-
You should go to the Archive on your camera and check image Thermal Resolution information there.
-
#902 Reply
Posted by
Marekx89
on 08 Jan, 2020 20:02
-
Much better menu ? Is any preview of menu ?
-
#903 Reply
Posted by
Bud
on 08 Jan, 2020 21:13
-
You did not bother reading this thread?
-
-
Sup?
I'm not the guy you replied to, but I just wanted to say two things. Firstly, your work on this thread is amazing and I can't thank you enough. As someone who may purchase a Flir camera down the line this is priceless.
Secondly, reading through the WHOLE thread may be out of reach for some, I know it is for me, I get back home and only get about an hour or two to spare, there's 37 pages (and counting) here. Maybe a nice index/summary at the top of page one would be useful to avoid these kinds of questions in the future.
-
#905 Reply
Posted by
Bud
on 09 Jan, 2020 02:39
-
Thank you. But we are not running a business here with a customer support team. Forums are free flowing discussions and individual contributors who are just like you go to work every day. Readers who are determined get rewarded for their efforts. I knew at the very beginning people will start asking for it, and I said they will have to do their homework and will not be spoon fed.
-
#906 Reply
Posted by
cream3000
on 09 Jan, 2020 06:37
-
[/img]
You should go to the Archive on your camera and check image Thermal Resolution information there.
is it 320x240?
-
#907 Reply
Posted by
Bud
on 09 Jan, 2020 14:38
-
This image is not from an E4, is it?
Secondly, this is a blended image (mix of thermal and visual) it is hard to assess.
Thirdly, you have to check the image Properties or Information in the Archive on the camera. There is a screen that tells you the Thermal Resolution and visual image resolution.
-
#908 Reply
Posted by
Bud
on 10 Jan, 2020 04:23
-
I guess you provided an image after you loaded it in Flir software and playing around with it. Here is the extracted raw thermal image, it is 320x240.
-
#909 Reply
Posted by
Marekx89
on 12 Jan, 2020 09:26
-
Ok, i have a upgrade menu, but add sketch in edit mode is not work good, cannot draw sketch. Whats a problem ?
-
#910 Reply
Posted by
Bud
on 12 Jan, 2020 19:40
-
The problem is you did not say what your problem is.
Edit: I've noticed you said your camera is E6. This thread and the liberation procedure is for E4 camera.
-
-
Brand new user/brand new owner.
Got an E4 2.0L w/3.16.0 firmware from Amazon today, and for those still thinking about buying one I purchased what I THOUGHT was Non-Wifi (s'what it said on
https://www.amazon.com/gp/product/B0115XR01C/)
I was pleasantly surprised to see "Wifi" on the box label, so either I got lucky or Amazon's goofing when it comes to their models. The part # on mine is 63906-0604.
Currently browsing go through the thread to find all the files/instructions necessary with the 3.16 version. Already snagged the Common DLL and backed up everything with WinSCP (Filezilla refused to work with Drag & Drop), so it's on to trying to do the configuration files next.
Wish me luck.
-
-
Welp, got the resolution hack working, attempted to upload the christmas pack however the design_ui.xml doesn't exist in the 3.16.0 edition, only design_ui_z3.xml.
Edited the code of that one, uploaded aaaaaand.. stuck on boot screen.
I've gotten everything backed up including that file, but due to it being stuck on the loading screen it won't connect to WIFI, however FlirInstall is still operational.
So if anyone has a FIF that could replace FlashBFS\system\ui.d\design_ui_z3.xml that'd be faaaantastic because that is really all I need.
Edit: Nevermind I got iiiiiiiiiiiiiiiiiiiiiiiiit!
Recalled that a FIF file is just a renamed .zip file with a command file along with the files that are to be replaced, so I created my own zip file and edited the Camera.cmd file to match what was needed. Said my prayers, fired it up, watched in anticipation as the splash screen appeared... and then after a flicker the splash screen with the "This Product is subject to US Export Regulations" popped up.
Needless to say, I did a rather.. boisterous cheer.
-
#913 Reply
Posted by
Bud
on 14 Jan, 2020 07:51
-
Sounds like you did not do the Advanced pack before trying the Christmas pack? The instructions for the Christmas pack say the Advanced pack is a pre-requisit.
-
-
I did, actually. Added medical.pal/toolbar-config.xml/etc.
I think I may have ended up not doing the Basic the whole way as there was no design_ui.xml when I did it, only design_ui_z3.xml which came with the camered. Adding design_ui.xml in the Advanced made no difference.
MY dumb self opened both files in Notepad++ (highly recommended software, btw) but I only really skimmed through so I noticed only a couple differences in the coding (and dimissing that one was 20kb larger than the other) before renaming the Christmas Pack design_ui.xml to design_ui_z3.xml and uploaded, and that's what caused it to freeze.
-
#915 Reply
Posted by
Bud
on 14 Jan, 2020 17:18
-
The instructions for the Advanced pack say the Basic one have to be installed first. Your problem was because you jumped all over the place making assumptions.
-
#916 Reply
Posted by
Bud
on 14 Jan, 2020 17:38
-
To new users:
follow the instructions to the letter to save yours and everyone else's time. If there are Pre-requisite requirements, do them first, they were put there for a reason. Any deviations and you are on your own.
-
-
Indeed. Tends to happen when I get excited about something (and when I have multiple things open at the same time) so I can lose my place.
...On another note, is it normal for the device to pause for 'Calibrating.." every thirty seconds or so during use?
-
#918 Reply
Posted by
Marekx89
on 15 Jan, 2020 18:47
-
ok, is possible set RNDIS from menu permanent ? I flash RNDIS permanent, but not select USB mode, still RNDIS. What is wrong ?
-
#919 Reply
Posted by
Bud
on 16 Jan, 2020 08:11
-
You cant change USB/RNDIS from the menu. Flir disabled that long time ago. This has nothing to do with the mod.
-
#920 Reply
Posted by
Bud
on 16 Jan, 2020 08:14
-
...On another note, is it normal for the device to pause for 'Calibrating.." every thirty seconds or so during use?
Whe you start the camera it does it often but as the camera warms up calibration becomes less often.
-
-
Worked perfectly for me with an 2.0L / 3.16 in Germany. I also liberated an E50 / 4.12 to higher resolution. Amazing!
-
#922 Reply
Posted by
Maxxpower
on 18 Jan, 2020 18:04
-
Please forgive me in advance if I ask a dumb question that has already been answered but there are a few E4 threads with hundreds of posts...
I have an E4 wifi that I successfully hacked (E4 2.0L 3.16)
Before the hack, the pictures saved on the device were 320x240 pixels, after the hack the images are still 320x240 pixels.
Is this correct?
Everything tells me the hack was successful but now I'm confused.
-
#923 Reply
Posted by
Fraser
on 18 Jan, 2020 18:37
-
The Ex series always produce a 320 x 240 pixel output, no matter what the the actual thermal image resolution may be. It is just upscaling. The true thermal image resolution may be seen in the FLIR Tools program in the image properties. If such shows 80 x 60, you know the resolution is not increased above a standard E4, if 320 x 240, the upgrade has worked and you have QVGA resolution on the E4.
Fraser
-
#924 Reply
Posted by
Fraser
on 18 Jan, 2020 18:46
-
Your images do not look like 320 x 240 thermal images to my eyes. Turn off the MSX overlay to see just the thermal image without the visible light detail That makes the image look better than it really is in the thermal domain.
Fraser