there are two beeps per edge detection of WAKE input.
Currently I have no buzzer. Are you sure it's that? It will beep when waking but also when reaching the temp.
So if you go to sleep and wake up quickly, both things will happen very closely in time.Well, it behaves like this:
https://youtu.be/Vbdyr-n5YeY
I did not see this behavior in earlier builds.
void setCurrentMode(uint8_t mode){
Iron.CurrentMode = mode;
buzzer_short_beep();
void setCurrentMode(uint8_t mode){
if(Iron.CurrentMode != mode){
buzzer_short_beep(); // Beep only when the system mode changes, you bastard!
}
Iron.CurrentMode = mode;
wow sweet can you tell me where to get that display? id love to get a few of them for mounting these into a combo type unit?
is this just with the quicko branded one? i dont have this issue with the ksger boards?
the newest posted ksger firmware (3.0 oled board on this one) id like to say is working amazing. temps are rock solid after calibration. i mean within 2-3 deg stable. very nice. thank you! this is with the china t12 tips also the real hakko ones are even more stable. i was able to get one to within 1 deg almost everywhere 2 max
Updated binaries! (Also the release v1.0 files)
wow sweet can you tell me where to get that display? id love to get a few of them for mounting these into a combo type unit?Search Aliexpress, Banggood, Amazon etc for 'SSD1309 2.42" OLED'is this just with the quicko branded one? i dont have this issue with the ksger boards?I see it on the KSGER 2.1 too.the newest posted ksger firmware (3.0 oled board on this one) id like to say is working amazing. temps are rock solid after calibration. i mean within 2-3 deg stable. very nice. thank you! this is with the china t12 tips also the real hakko ones are even more stable. i was able to get one to within 1 deg almost everywhere 2 maxAgreed, great upgrade for the 3.0 board!
Updated binaries! (Also the release v1.0 files)Wow, fast work! It did get better, only one beep per input now (Tested the .bin straight from github on my KSGER 2.1)
Updated binaries! (Also the release v1.0 files)Wow, fast work! It did get better, only one beep per input now (Tested the .bin straight from github on my KSGER 2.1)Wait, does it still beep when you shake the handle? It should -only- do it when entering or exiting sleep mode.
Or when you change the temp and it reaches the setpoint.
almost everyone i can find has the pins down the left side ill look again. there wouldnt be enough clearance that way how i want to mount them where yours has them on the top. ill take another look maybe i missed it. was the one you have solder and go or did you have to modify it at all? i have a source for the 1.3" that are VERY close fitment wise to the stock ones just a hair lower and are exact pin out. thanks
If you disable the buzzer it stops doing it?
Just to be sure it's the buzzer call.
Guys, I'm thinking on changing to a new thread. Since I didn't made this one, it's impossible keep this tidy.
I would like to use the first post as an quick FAQ for the troubles / fixes / questions that usually appear, also maybe announces/updates.
AndyC, also happens with the Quicko?
wow sweet can you tell me where to get that display? id love to get a few of them for mounting these into a combo type unit?Search Aliexpress, Banggood, Amazon etc for 'SSD1309 2.42" OLED'
almost everyone i can find has the pins down the left side ill look again. there wouldnt be enough clearance that way how i want to mount them where yours has them on the top. ill take another look maybe i missed it. was the one you have solder and go or did you have to modify it at all? i have a source for the 1.3" that are VERY close fitment wise to the stock ones just a hair lower and are exact pin out. thanksThis looks similar to the one I got: https://www.aliexpress.com/item/4001250463926.html
I just soldered the header pins and connected it
do you need simple calibration measurements or do you need separate ones from different tip styles?