This is interesting for me because I recently ordered the same module, except in green.
You look like you machined that case out of solid metal!?
Anyway, i am sure your device is going to look just great.
Nice!The manual, such as it is, is here: http://www.cwtd.org/frequency/RF%20Signal%20Frequency%20Counter.pdf
Nearly completed the enclosure, rather tricky to get the hole spacings correct - electronic PCBs are not an exact science it seems and unlike engineered bits dimensions can vary :-) So it was tricky transferring relative positions to a chunk of metal. Anyway, the basic thing is done - I'll make some nice captive button caps and when the BNC panel plugs eventually turn up they will go on the LH side. I'll install a power switch on the front and a 2.5mm DC input jack on the back. In one of the pics you can just see the heatsinks I installed.
Quote from: cdev on Today at 11:31:51 AMThis is interesting for me because I recently ordered the same module, except in green.
You look like you machined that case out of solid metal!?
Anyway, i am sure your device is going to look just great.
Nice!Yes mine are also green
They offer an excessively bright display though and only need to be set to brightness level '3' (out of 8 ), but I've also ordered some dark green acetate (L124 "Dark Green") to go over the front to improve readability and that only has 30% transmission so I may need to increase brightness a little. Link
http://www.ebay.co.uk/itm/Full-Sheet-of-Lee-Filters-L124-1-22m-x-0-53m-colour-acetate-stage-lighting-gel/331476995250?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m1438.l2649It's not solid metal but alloy box-section, which I have a lot of
. It's a lot cheaper than buying discrete project boxes and you can make a lot of small boxes from one 3M length! However I should have machined off the front face _first_ then cut out the holes but like an idiot I did it the other way around and the narrow strip between the two displays really didn't like being fly-cut because there was little support remaining and it chattered. Oh well.
Still, it's a cool enclosure, Chris. I like it.
An Agilent 34401a, to go with the voltage reference and lead set I got earlier :-)
In pristine condition, supposedly coming from a cleanroom. The only drawback is the display; by the looks of it it spent its days in 5 digit mode, as the 6th digit is the most clear (and the least worn). Well, a new display is always a possibility; for now I am quite happy with this meter.
The only drawback is the display; by the looks of it it spent its days in 5 digit mode, as the 6th digit is the most clear (and the least worn). Well, a new display is always a possibility; for now I am quite happy with this meter.
There's a thread on rejuvenating a VFD, one post in particular that might be of interest to you (
here).
Hope this is of some help to you.
An Agilent 34401a, to go with the voltage reference and lead set I got earlier :-)
In pristine condition, supposedly coming from a cleanroom. The only drawback is the display; by the looks of it it spent its days in 5 digit mode, as the 6th digit is the most clear (and the least worn). Well, a new display is always a possibility; for now I am quite happy with this meter.
how much it costed?
am searching for a used 6.5 digit dmm for a while. it's bit confusing which model to go.
Sent from my 6043D using Tapatalk
For anyone who was curious, here's the other side of those boards. I never realized how hard it is to take a clear picture of a circuit board. (If you can't make it out, the text at the top of the three boards reads "CROMEMCO ACC-1", "CROMEMCO ACC-2" and "CROMEMCO ACC-3")
I finished the job on the frequency counter enclosure, and in the end I installed a couple of Nemo sockets because I have quite a few lying around (and patch cables + Nemo>BNC adapters). Out of curiosity I trawled ebay for the cost of these connectors and nearly fell out my chair!
I turned up some captive button caps from stainless rod, whilest on the back is the 2.5mm DC jack socket, a toggle switch, and two holes which line up with the trim pots for callibration. Four 3M sticky feet and the job's done :-)
Very nice and neat job, when I did mine I used a piece of coloured acetate in front of the display to hid the unused digits. Why two counters in the same case, plus the other frequency counter?
My next 2 year long project.....
An HP3577A network analyzer. Fingers crossed it has an obvious and easy problem that prevents startup.
I have missed buying one of these twice.
I want one !
I have missed buying one of these twice.
I want one !
So you're essentially saying this?
It just arrived today. My goodness, such a strange choice for it's RF connector!
The manual, such as it is, is here: http://www.cwtd.org/frequency/RF%20Signal%20Frequency%20Counter.pdf
Nearly completed the enclosure, rather tricky to get the hole spacings correct - electronic PCBs are not an exact science it seems and unlike engineered bits dimensions can vary :-) So it was tricky transferring relative positions to a chunk of metal. Anyway, the basic thing is done - I'll make some nice captive button caps and when the BNC panel plugs eventually turn up they will go on the LH side. I'll install a power switch on the front and a 2.5mm DC input jack on the back. In one of the pics you can just see the heatsinks I installed.
Not that your boxes look bad or anything, they actually are quite well done, but just for future reference it's sometimes possible to mount boards from the back side of the box, resulting in a little bit cleaner look. It is a little more trouble getting it all to align correctly though.
If screws need to be at the front of the panel, there are many ways to make it a design feature. The screws in this case look pretty good. I would even go further and make a "safety bar" type design from threaded u-shaped rods, like the handles used on 19in Audio gear.
McBryce.
Somehow lost the picture in my previous post.
This is sort of what I was suggesting. I used regular 4-40 standoffs, just went in from the back. There was enough clearance on top of the board for the display to still mount flush with the inside of the lid. There wasn't much I could do about the screws holding the lid on though.
Oh nice job, and quite do-able if you have a lid, my box is just solid rectangular alloy section though - no lid - and the PCB assembly(s) need to be slid into position from the end.
In fact, by the time I have made a cover to hold the dark-green gel contrast enhancer (using something akin to a picture frame to hold it in place) you probably won't see the screws anyway. I haven't planned this out exactly (like I should).
My next 2 year long project.....
An HP3577A network analyzer. Fingers crossed it has an obvious and easy problem that prevents startup.
That's verrah naace. Does it do anything (besides weigh a ton or three)? I don't think I ever found a service manual for that one, but also don't recall looking terribly hard for one, either.
-Pat
Found another plug in for the 2x 5245Ls, 10 down, 4 to go
I missed out on decade box I've been eyeing for the past week. Why, you ask? Because I forgot to bid
I intended to sneak in a bid at the last moment, since no one had bid so far, but I got distracted by dinner and was too late. It was sold at a bargain price too.
I'm a proper retard. Quite literally.
Done that a few time and, just like you arrived a minute too late or completely forgot.
Got one of these cheap timers that goes up to 99h and fits in your shirt pocket for about $3.
Set and forget once you see something of interest.
Works wonders to beep me about 5 minutes prior to the end of the auction.
Done that a few time and, just like you arrived a minute too late or completely forgot.
Got one of these cheap timers that goes to goes up to 99h and fits in your shirt pocket for about $3.
Set and forget once you see something of interest.
Works wonders to beep me about 5 minutes prior to the end of the auction.
Just install their app on your phone and it will alert you 15 minutes before the auction ends.
McBryce.
Gesendet von meinem Motorola DynaTAC 8000x mit Tapatalk
Just install their app on your phone and it will alert you 15 minutes before the auction ends.
McBryce.
Gesendet von meinem Motorola DynaTAC 8000x mit Tapatalk
I'm not sure how that alert is implemented, but if it supposes a continuous internet connection, it's no more reliable than my own memory. I also think I'm not too fond of the idea of an eBay app and the things it might track, index and send home. Setting the existing alarm manually should do too.