-
#8225 Reply
Posted by
mario.ti
on 16 Apr, 2017 11:36
-
Xavier64I keep my fingers crossed for the guys, in another topic,
here.
The same as you, i'll try to help if needed
-
#8226 Reply
Posted by
Simon
on 16 Apr, 2017 12:42
-
Edit: The fubar site has a section on switching the flir to RNDIS mode. This worked for me, but when I first did it, my computer and flir froze up for a while until I finally decided to unplug the flir from the usb, and as soon as I did, every thing unfroze. Then when I plugged the usb back into the flir, it was in RNDIS mode and it finished setting up with an IP address. The main thing is if it freezes during this step don't be afraid to unplug the usb to get it going again.
He just says to plug the camera in and use the fif file to set RNDIS mode but I can't get into it in the first place.
-
-
So you are saying that you installed the FLIR device drivers, Flir Tools, Python 2.x (3.x won't work) first. Then when you plug the USB in what happens? Does windows install the device drivers automatically? If not are you sure you hadn't already done this previously? Then what happens when you run the FLIRInstallNet.exe program? Are you saying this doesn't connect to the camera? Or it does but gives some other kind of error when you try to have it load the Set_RNDIS_permament.fif file?
Sorry, if those steps don't work for you I'm not sure what else to suggest. I followed the fubar guide exactly (except used the 2.11 hack files instead of the 2.3 hack files) and it worked for me with only the minor hiccup that I had previously mentioned that required me to unplug the usb to continue.
Edit: This may seem obvious but better to mention it to make sure. When you plug the USB into the Flir, be sure to turn the Flir on.
-
#8228 Reply
Posted by
tokotak
on 18 Apr, 2017 16:32
-
@Pauloven,
.................... I will then work on sorting out the image inversion in the Inframatrics X3 telescopes. Note that the Inframetrics Telescopes are circa 1980's but the optics are superb quality. These cost me around $150 on e*ay. Bargain lenses, even though they invert.
Aurora
As a happy new owner of pm595 I've read almost all your comments here with great interest. Though some questions remained.
How do you fit or plan to fit Inframetrics X3 on pmXXX series cameras? The mounts seems to be different.
-
#8229 Reply
Posted by
Fraser
on 18 Apr, 2017 17:14
-
I have a 7x12 lathe to make mount adapters
The Inframetrics X3 lenses have a removeable bayonet mount that is a thread fitting onto the lens body.
Fraser
-
#8230 Reply
Posted by
tokotak
on 18 Apr, 2017 20:34
-
I have a 7x12 lathe to make mount adapters
The Inframetrics X3 lenses have a removeable bayonet mount that is a thread fitting onto the lens body.
Fraser
I see. What are your findings on the Inframertics lens image circle? Is it bigger,equal or smaller then in original Agema/Flir design?
If the distance between the attached Inframetrics lens with the adapter and the main one allows the optical path to be perfect or just usable?
-
#8231 Reply
Posted by
Fraser
on 18 Apr, 2017 21:40
-
You really need to start a new thread if you want to discuss auxiliary lenses for thermal cameras.
I am not very active on this forum at the moment so my responses will not be quick
Fraser
-
#8232 Reply
Posted by
tokotak
on 19 Apr, 2017 08:14
-
-
#8233 Reply
Posted by
god_ukr
on 21 Apr, 2017 23:04
-
Hi everyone!
Can anyone point me where Flir E4 can be purchased with discount?
Before I used Zoro, but now Flir in exception list for discount
PM please
-
#8234 Reply
Posted by
Xavier64
on 27 Apr, 2017 17:14
-
I want to sell my Flir E4+, its brand new and still under warranty. Just PM me.
regards
-
#8235 Reply
Posted by
sofi
on 02 May, 2017 18:28
-
Friends something new? Did anyone unlock 3.5.0?
-
#8236 Reply
Posted by
djeans
on 16 May, 2017 09:43
-
Hi Friends, I now have a 1.18.7 FW with 1.0 HW Flir E4.
is it possible to hack this one too and what files are required? This thread is really long. Can anyone point me please into the right direction
thank you
DJ
-
#8237 Reply
Posted by
Fraser
on 16 May, 2017 10:52
-
The very first post of this thread has links to specific areas of the thread for different versions of the firmware and hardware. You will find all that you need via the link that covers the 1.18 or 1.19 firmware. An update to the 1.19 firmware is not necessary in case you are wondering. Do not update to any firmwRe after 1.19 as they were created by FLIR to make the upgrade harder to achieve.
Fraser
-
#8238 Reply
Posted by
djeans
on 16 May, 2017 14:15
-
Thank you very much Fraser, I followed the 1.19 guide for my 1.18.7 and worked very well.
So doing an update to 2.30.0 ist not required, right? An no benefit also, or?
-
#8239 Reply
Posted by
Fraser
on 16 May, 2017 16:12
-
In my opinion, it is not a good idea to update the firmware beyond 1.19. I spoke to a FLIR tech and it was his view that any firmware after 1.19 was more about preventing the upgrade than fixing any firmware issue. He knew of no bugs in 1.19 that needed to be fixed as it was stable and fit for purpose.
I am a genuine thermal camera Geek and own two E4's. They are both running firmware 1.19. Never had a problem with 1.19.
IIRC 1.19 firmware was not released as an upgrade for 1.18. Worry not though, 1.18 is just fine.
Fraser
-
#8240 Reply
Posted by
joe-c
on 16 May, 2017 21:04
-
FW up to 1.19.8 could be calibrated with the Webpage inside the camera.
and they are easier to "enhance"
.
But FW above 2.3.0 have a Thermal Blending mode and can used for RAW Streaming (i never did, but some other with Linux).
Additional its possible to turn off all GUI stuff like scale and Spot cross, for a real thermal view (interesting for video recording over UVC).
And you can change the MSX Distance directly from the View-Mode-Menu.
i think both Versions are not bad
-
#8241 Reply
Posted by
Fraser
on 16 May, 2017 21:40
-
@ Joe_c
I agree, there is nothing actually wrong with any of the FLIR E4 firmware versions (except the already identified buggy version that FLIR fixed quickly)
The versions that FLIR released after 1.19 sadly lost some OS functionality and had 'protection' added to make life harder for upgraders. It was understandable, but still a pity. The E4 is an amazing platform in terms of what it can provide for the purchase price, once upgraded. In 1.19 the configuration is so easy to customise that it may be 'tuned' to the users desired configuration. The ability to access the service menu is also a reason for me sticking with it. I do not need video streaming but that is certainly a nice addition to later firmware.
I tend to think it best to stick with 1.19 until a feature available in 2.3 is actually needed.
Fraser
-
#8242 Reply
Posted by
plurn
on 17 May, 2017 16:05
-
I just noticed a new firmware version for Ex on the flir support site:
FLIR Ex (3.9.0) Update Pack
Last Updated: May 9, 2017
... FLIR Ex series cameras (S/N prefix: 639). ...
I have no intension of upgrading to that.
-
#8243 Reply
Posted by
nos_com71
on 23 May, 2017 11:17
-
just to confirm ,steps to upgrade E4 2.11.0 1.2L went smooth only by using a vrtual XP , look for it in Microsoft site (WindowsXPMode_en-us) ,it free and easy to use.
good luck
-
#8244 Reply
Posted by
ollihd
on 30 May, 2017 06:39
-
Just got my E4 back from warranty repair (previous posts show my problems). Well of course they updated the HW to 2.0L and firmware to 3.9.0. Is there any new news about getting this hacked or should I start selling my E4?
-
#8245 Reply
Posted by
chili_red
on 03 Jun, 2017 19:22
-
Does anyone happen to have the 2.11.0 upgrade file they could upload, the links I found in this thread are no longer working.
TIA
Steve
-
#8246 Reply
Posted by
nos_com71
on 04 Jun, 2017 17:14
-
-
#8247 Reply
Posted by
ollihd
on 07 Jun, 2017 16:27
-
Does someone know if anyone is working on hacking the 3.5.0 or 3.9.0 FW? Would be happy to help as much as I can!
-
#8248 Reply
Posted by
Fraser
on 07 Jun, 2017 18:30
-
-
#8249 Reply
Posted by
mb100
on 09 Jun, 2017 22:50
-
Hello: I am fighting a little bit with the Flir e4. Version 1.2L.
when I try to perform the ftool decryption, decryption fails on "tail part 2". I am not sure if I understand the c# code correctly, but I think that means an early step with a mismatch. I ftp,ed the file with the windows command line and also with core ftp lite (filezilla n/a for windows xp) - same problem so i don't think it is a potentially corrupted conf.crc file, but really the ftool itself that produces the error.
Can you advise if there is an updated ftools to be used for camera version E4 1.2L (not 1.22) sw 2.11.0