A capacitor or a dick head who has been in it previously or touched it or looked at it funny
Well done med
50 ohm inputs on both channels fixed.
But the 1M input both channels still low gain. That will be tomorrow's to do.
I guess I'm going to have to do a re-cap of the PSU. For now just do the tants. A full re-cap of the PSU including the electrolytics runs over $60 USD.
Show us what that cal Iout edge looks like on a 1ns/div timebase. It isn't a run-of-the-mill cal out
"Kill them all. God will know his own." ~Abbot Arnaud Amalric med the Tant-Slayer strikes again!
mnem
*egregious*
Haha, thats what we used to say about bd139, back in his Tek days
Haha, thats what we used to say about bd139, back in his Tek days
He doesn't know what day he's in.
I’ve retired to the greener and less tanty pastures of HP, philips and hameg.
Until a 7L12 comes flying across your radar.
Most depressing use of ArcGIS ever
On a knob mission tonight for the PM3217...
Printing first one now
Edit: also bought a new fancy switch the other day. It's a diddy little barnacle one you can stick to the radio (and doesn't weigh over 1Kg).
I never could get the hang of the paddle; straight key was hard enough.
Scary part is... there's 5 confirmed cases in all of the Americas... and one of 'em is less than 20 kliks away from me.
mnem
Or it could be that release of radioactive material at Pickering GTA nuclear power plant "that never happened"...
Been soak testing the PL320 ... require 1 knob cap ... part number Cliff CL1764 K21
Thank you so much for posting that part number! After a quick eBay search and some waiting, my PL320 has never looked better!
(Well, apart from the one missing link bar.
)
Looking good
. You can actually get the shorting bars from Aim-TTI I think. Min order was £5 so that means buying a lot of them. I was going to buy 100 or so and ebay them for a cranked up price
I never could get the hang of the paddle; straight key was hard enough.
Scary part is... there's 5 confirmed cases in all of the Americas... and one of 'em is less than 20 kliks away from me.
mnem
Or it could be that release of radioactive material at Pickering GTA nuclear power plant "that never happened"...
Paddle is cool as it does the spacing for you. Takes a while to learn though and I fudge it all the time I'm a lazy fucker so it's good enough
Don't think we've had any cases here yet. Everyone was cleared. I live in the disease "hot zone" i.e. local to the largest national airport. Everyone works there here. Ugh.
First attempt - shaft hole fractionally too small. Opened up by 0.2mm. This is why it's better to do it at home than order it
Most depressing use of ArcGIS ever
You can do 3D with ArcGIS? I need to talk to my wife.
Also: figured I'd ask here first. Anyone from the Houston, TX area that would be interested in a paying job? Either paying in cool stuff or paying in cold hard cash, all fine by me.. If you have a thrustworthy friend or relative, that works too..
May have found the immediate problem, but that near-break in the wire loom at the bottom looks mighty risky to me!
somebody got their iron on that
I didn't even notice that. Thanks. The wire is OK, just some insulation char. It wasn't me. That pix was taken before I removed the parts.
Looking good . You can actually get the shorting bars from Aim-TTI I think. Min order was £5 so that means buying a lot of them. I was going to buy 100 or so and ebay them for a cranked up price
Thanks, the two missing end caps were bugging me, but I had no idea that they could still be purchased, much less what to search for. I think I hit the "Buy" button within seconds of reading Specmaster's post.
I couldn't find the shorting bars on Aim-TTI's web site, so I just looked at my local metal supplier. I can get half a metre of 3mm x 15mm pure copper plate for less than a fiver, so I reckon I'll just make some new bars myself. Maybe I'll even give my "engraving" machine a challenge and see if I can mill some!
Also: figured I'd ask here first. Anyone from the Houston, TX area that would be interested in a paying job? Either paying in cool stuff or paying in cold hard cash, all fine by me.. If you have a thrustworthy friend or relative, that works too..
Fuck you very cordially.
A year ago, sure. No longer there now of course.
Thrustworthy...? ehhh... nope. Not even with a borrowed dick and someone else pushing.
mnem
And no, I don't know ANYONE in Houston I'd trust as far as I could sling a piano... that's half the reason I'm not there anymore.